工廠對于鈑金機箱機柜的生產具有相應的技術和工藝。而在不同的環境下不同氣氛的影響會給機箱機柜帶來不同的效果，所以根據不同的情況我們需要對機箱機柜進行整體處理。

The factory has corresponding technology and process for the production of sheet metal chassis and cabinets. The influence of different atmospheres in different environments can bring different effects to the chassis and cabinets, so we need to treat the chassis and cabinets as a whole according to different situations.

對于鈑金機箱機柜來說其擁有良好的外在形象，而長時間的戶外工作則會給其帶來很大的影響，所以說對于機箱機柜的鈑金外殼進行的表面處理則會給其帶來很高的影響。

For sheet metal chassis and cabinets, they have a good external image, and long-term outdoor work can have a great impact on them. Therefore, surface treatment of the sheet metal shell of the chassis and cabinets will have a high impact.

在對機箱機柜進行表面預處理的過程中可以對其進行表面噴塑或者噴漆處理，這樣根據不同的具體情況我們可以選擇合適的方法來增加鈑金機箱機柜的使用壽命和年限。

During the surface pre-treatment process of chassis and cabinets, surface spraying or painting can be applied. This way, according to different specific situations, we can choose appropriate methods to increase the service life and service life of sheet metal chassis and cabinets.

眾所周知，機箱機柜的外殼都是用鈑金制成的。各個部件均采用不銹鋼軋板，聚眾聯合在對加工的機箱時行驗收時一定要注意幾點：

As is well known, the casings of computer cabinets are made of sheet metal. All components are made of stainless steel rolled plates. When inspecting the processed chassis, it is important to pay attention to the following points:

1、鈑金機柜不允許有肉眼可見傾斜或局部歪、扭現象存在?？蚣芰⒅c底座垂直度為小于1.5mm。檢測時以底座上表面為基準，以立柱上端內沿面為測量點。

1. Sheet metal cabinets are not allowed to have visible tilting or local tilting or twisting. The verticality between the frame column and the base is less than 1.5mm. During inspection, the upper surface of the base is taken as the reference and the inner edge surface of the upper end of the column is taken as the measurement point.

2、頂框與底座平行度為小于1mm。檢測點為底座上表面及頂框下表面，且互為基準。也可通過測量六面之對角線的長度，相差不得超過2.5mm來檢測。有中隔板者，頂框與底座平行度可放寬1.5mm，中隔板與頂框或底座平行度為小于1mm。

2. The parallelism between the top frame and the base is less than 1mm. The detection points are the upper surface of the base and the lower surface of the top frame, and they serve as benchmarks for each other. It can also be detected by measuring the length of the diagonal of the six sides, with a difference of no more than 2.5mm. For those with a middle partition, the parallelism between the top frame and the base can be relaxed to 1.5mm, and the parallelism between the middle partition and the top frame or base should be less than 1mm.

3、上、下圍框的對角線之差的值小于1.5mm。

3. The absolute difference between the diagonal lines of the upper and lower bounding boxes is less than 1.5mm.

4、立柱不能有扭曲現象，各立柱與上、下圍框相連的兩端交接線與圍框相鄰平面的平行度為小于0.5mm。

4. The columns should not have any distortion, and the parallelism between the intersection lines at both ends of each column connected to the upper and lower frames and the adjacent planes of the frames should be less than 0.5mm.

5、支撐插箱的滑道，同一層的左、右滑道所組成的工作面相對底座上表面的平行度為1mm，且應保證插箱裝入后相鄰兩面板之間間隙之差的值不得超過0.6mm。

5. The parallelism of the working surface composed of the left and right slides on the same layer supporting the insertion box with respect to the surface of the base is 1mm, and it should be ensured that the absolute difference in gap between adjacent panels after insertion of the insertion box does not exceed 0.6mm.

本文由濟南機箱機柜友情奉獻.更多有關的知識請點擊: http://m.kisansushi.com真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is a friendly contribution from Jinan chassis and cabinets. For more information, please click: http://m.kisansushi.com Sincere attitude. We will provide you with comprehensive service. We will gradually contribute more relevant knowledge to everyone. Stay tuned